DC Brushless Motor Automatic Parking Lot Barrier Gates DC24V Motor
Wonsun is a professional manufaturer for barrier gate, boom
barrier, sliding gate motor. If any interest, please contact me
Whatsapp: +86 185 0748 1610
1 Working temperature(motor): -35℃~+85℃
2 Rated voltage:DC24V
3 Running speed:1.5s-8s
4 Rated current:8.58A
5 Rated power:140W
6 No-load speed:1850rpm
7 Rated speed:1400rpm
8 Output Power:56.8N.m
9 Relative humidity:≤90%
10 Remote control distance:≤100M(in the open place)
11 IP Degree:IP44
12 Max length of arm:6M
1 The running speed can be adjusted from 1.5s to 8s
2 Can be quickly interchanged
3 Open the barrier gate by motor wheel when power off
,automatically reset after power on
4 Curved crank arm three- link movement structure, the operation is
5 Wireless remote control control open/close
6 Auto reverse function(force adjustable)
7 Infrared photocells connector is available
8 Loop detector connector is available.
9 Well-integrated with car parking system equipment,with wire
control(must be switch signal)
10 Connector for traffic light(AC220V,power less than 40W)
11 Offering dry contact signal for car parking system(COM,NC,NO)
12Auto-delay when closing(adjustable)
13 RS485 or CAN network communication interface(no need to install
14 Counting interface
15 24V backup battery interface(Can be charged by using solar
Arm length speed comparison table
|Menu code||Number||Menu code name||Defaults||unit||Remarks|
|H00-00||25-95||Open speed adjustment||40||Corresponding PWM duty cycle 25%-95%, step size is 1|
|H00-01||25-95||Close speed adjustment||40||Corresponding PWM duty cycle 25%-95%, step size is 1|
|H00-02||5-40||Open in place decelerate angle||35||The larger the angle value, the less likely it is to shake the arm
when it is in place.|
|H00-03||5-40||Close in place decelerate angle||35||The larger the angle value, the less likely it is to shake the arm
when it is in place.|
|H00-04||1-20||Open accelerate adjustment||10||ms||The smaller the number, the faster the speed|
|H00-05||1-20||Close accelerate adjustment||10||ms||The smaller the number, the faster the speed|
|H00-06||1-30||Open in place angle||2||degree||step size is 1|
|H00-07||1-30||Open in place angle||1||degree||step size is 1|
|H00-08||7-13||Auto reverse force adjustment||10||A||step size is 1|
|H00-09||0-90||Delay closing adjustment||0||Sec||step size is 100；0 is not closing automatically,,Other value will
be closing automatically;This parameter is for when there is no
loop detector signals and non-automatic operation occasions|
|H00-10||10-50||Self-check speed adjustment||30||Corresponding PWM duty cycle 10%-50%, step size is 1|
|H00-11||0-2||Self-check mode||0||0:no operate automatically；1:operate automatically,remove after
power off；2:operate automatically,Power failure memory|
|H00-12||0-5||Self-lock force adjustment(Invalid)||3|
|H00-13||1-20||Motor deceleration time when paused||5||The larger the setting, the longer the pause time will take|
|H00-14||0-1||The default direction of operation after self-test||0||0:Closing,1:opening|
|H00-15||1-10||Number of pole pairs(Invalid)||4||Only used to correctly display motor speed values|
|H00-16||1-32||RS485communication address||1||Up to 32 slaves can be connected|
|H00-17||0-2||RS485communication rate||0||0:9600,1:19200,2:38400；Change the parameter and will be valid after
power on again.|
|H00-18||0-1||If self-test after power is on||1||0:no self-test after power on,1:self-test after power on|
|H00-19||0-3||Manual self-test adjustment||2||0:Manually invalid,1:Keyboard SET button,2:remote control
valid,3,Keyboard SET button and remote control both valid|
|H00-20||0-15||Monitoring parameter setting index||7||7,operation times(ms):0~9000|
8,Cumulative operation times:0`99999999
9,automatically operation times :0~99999999
11,Closing in place times:0~99999999
12,Power-on time (minutes):0~99999999
14,Input port status:Binary display
|H00-22||0-1||LED output mode||0||0:Do not flash alternately during operation；1:Allow flashing|
Q: What's the order process?
A: Follow the steps on below to complete your order.
- 1. Inquiry
Provide us detailed information about your requirement, and we'll
recommend the suitable products according to your request
Official quotation form with all clear specifications according to
Invoice will be issued once the quotation is confirmed.
Payment shall be issued once the invoice issued. Full payment is
Bulk production shall be taking 15-25 working days.
by sea, air or courier. Detailed picture of package will be
provided upon the service you've chosen. Packaging info will be
sent upon confirmation.
1 One year’s free servicing is supplied(not including the arm);
2 Lifetime charged servicing is offered;
3 Technology servicing is supplied.
The following situations are charged for servicing(or changing):
1Broken by the wrong installation.
2Broken by improper voltage.
3The surfaces of the system destroyed by wrong installation or use.
4Broken by natural disaster.
6Servicing items out of our promises.
1 Keep the barrier gate clean
2 Check the joints ever month in case of any loose parts.
3 Check the spring elasticity after the barrier gate running 3000
4 Check the easily worn-out parts(like the spring,limit
switch),every half year and renew it.
5 Remote control distance will be shortened or not work in case
like big object screening,battery exhausting,extreme weathers.