OEM Photocell Parking Lot Barriers For Car Parking Management
Car Parking Barriers Kit
1 * motor
1 * boom (from 1m to 6m can customised)
1 * control panel
2 * remote controllers
WSTP-115 (WONSUN 1st generation machine core)
Cold roll plate, Galvanized plate or stainless steel
varnish baking, 3 years without fading
0.6s, 1s, 1.8s, 3s, 6s
-45°C to 75°C
220V ± 10%, 110V ± 10%
<90% coagulation free
Max 6 meters
≥5, 000, 000 times
Straight arm: Mar 1- 6 meters optional, size 45×100mm aluminum
Folding arm: 90°folding arm / 180°folding arm, aluminum alloy
Fence arm: Two or three fence arm, Mar1- 6 meters, aluminum alloy
infrared sensors, loop detectors,traffic light, UHF readers
Parking Lots, Toll Gates, Goods Yards, Railway Crossings,
Commercial Premises, Aparment Block
1. quick delivery time, 3-5 days for 50 sets after received advance
2. 7 years OEM/ODM experience
3. quick response for handling problems
|Our other products|
WONSUN has other products: tripod turnstiles, sliding gate motor,
flap barrier,swing gate motor,
pedestrian access control turnstiles and barriers,
and other related accessories.
Functions & Features:
1. Manual release
2. Machine core with compression spring, effectively avoids the
accidents caused by spring breaking
3. Die-casting aluminum alloy motor, precision and good at thermal
4. Motor cooling fan, solving the problem of heat-protection
5. Double safety limit switches (photoelectricity limit
switch/motor memory sensor)
6. Reversing on obstacle
8. Support the INFRARER PHTOCELL for anti-bumping function
9. Support the external and internal VEHICLE LOOP DETECTOR
10. Traffic light interface
11. Wire control (switch signal)/ Remote control (418MHZ)
12. RS485 communication module (optional)
Parking & Shipping:
|Machine core||Good in working||1||Main part|
|Barrier arm||Straight, folding or fence arm||1||Optional|
|Boom press board||1||Fixing the boom|
|Self-tapoing screw||ST4*16||Fixing the boom|
|Self-tapoing screw||st3*10||4||Fixing the boom|
|Supporting pole||1||Fupporting the boom|
|Expanion bolt||M16*150||4||Fixing the case|
|Hexagonal Inner Screw||M8*35||4||fixing the case|
|Clutch key||1||clutch device|
|Case Key||2||for case and cover locking|
|Balance spring||According to length of barrier arm||1||for sapre usage|
|Remote emitter||less than 30m is available||1||For remote control|
|Remote conrol handles||less than 30m is available||2||For remote control|
|Instruction||in English||1||For reference|
|Cover head||1||3 years without fading|
|Expanion nut||M8||4||Fixing the supporting pole|
Communication with customers
1) Q: Connected power and press open/close button but traffic
barrier gate no action?
Check fuse and power in controller
Battery of remote control powered off
Change a new one
External protection circuit break or at protecting status
Open the barrier door and click OPEN/CLOSE button on control box
Same frequency interference
Check photocell and loop detector
2) Q:Connected power and press open/close button,traffic barrier
gate will move but even when it is at right position, the motor
still running and not stop?
Adjust the horizontal/vertical limit switch to correct position
Main controller failure
Change a new one
3) Q: Motor running but traffic barrier gate arm no action?
Barrier arm at 45° position where is hard to move
Unlock clutch and manually rotate arm to horizontal or vertical
position then try again
Tension of balancing spring not suitable
Adjust spring exactly
Low working voltage
Check the voltage and power
4) Q: When opening/closing,traffic barrier gate arm cannot reach
right position (90° vertical & 180° horizontal)?
Length adjustment of connecting rod not correct
Open barrier door and unlock clutch to check when arm at 90° vertical position if the master rod covers slave one; when arm at
180° horizontal position if master rod and slave one are in the same
Nuts on the limit switch loose
Tighten the nuts when arm at 90° vertical and 180° horizontal position
1. Are you manufacturer or trade company?
We're professional manufacturer who has our own factory in Shenzhen
Pingshan since 2007.
2. What is your MOQ?
As for usual order, there is no MOQ; For OEM order, at least 30
3. What is your delivery time?
As for usual order, it is 3-5 days after received your payment with
50 sets order quantity.
For OEM order, it is 7-15 days after receieved your payment with 30
sets order quantity.
4. What is the terms of payment?
30%-40% advance deposite, 60%-70% balance before shipment for large
5. How long will your gate barrier working?
Gate barrier life span is 5-10 years.
6. What should we do if there have problems during using?
My dear friend, We have 1 year guarantee. Any gate barrier problems
you have, Welcome email or
call me! We will provide our best professional service for you.
7.How to import your machines?
* We will prepare gate barrier and shipment for you after payment;
*We will give you bill of loading after gate barrier depart our
*Our shipping agent will contact you when gate barrier arrival